GMFisher Posted December 23, 2018 Report Share Posted December 23, 2018 Hi, Have been using your Flirc product for a while now and really enjoy the convenience it offers. Rebuilt my system, which included new versions of Flirc software and answered yes to the "Update Firmware?" question on my WIndows 10 machine. The upgrade appeared successful and tests on the Win 10 machine are successful. Config settings still there! Load a fresh image of Moode 4.4 and the keystrokes no longer register on the Pi 3. I have a Ver 2 (nemo) hardware dongle. Have tried it in all 4 USB ports, rebooting each time. It is definitely a Linux issue. I suspect the driver is not loading properly? But it shows as loaded in 'dmesg' below. The dongle works with Windows 10. The remote works with the dongle in Windows 10. Transfer the dongle to a freshly written Moode 4.4 image and the key strokes are not sent. It WAS working fine before the firmware update. Any help would be greatly appreciated. [ 3.431515] usb 1-1.5: new full-speed USB device number 4 using dwc_otg [ 3.576263] usb 1-1.5: New USB device found, idVendor=20a0, idProduct=0006 [ 3.586162] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.596423] usb 1-1.5: Product: flirc [ 3.602937] usb 1-1.5: Manufacturer: flirc.tv [ 3.612351] systemd: Listening on RPCbind Server Activation Socket. [ 3.622330] hid-generic 0003:20A0:0006.0001: hiddev96,hidraw0: USB HID v1.11 Device [flirc.tv flirc] on usb-3f980000.usb-1.5/input0 [ 3.643843] systemd: Listening on Syslog Socket. [ 3.652207] input: flirc.tv flirc as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.1/0003:20A0:0006.0002/input/input0 [ 3.672769] systemd: Created slice System Slice. [ 3.684549] systemd: Created slice system-serial\x2dgetty.slice. [ 3.699676] systemd: Mounting RPC Pipe File System... [ 3.712408] systemd: Listening on udev Control Socket. [ 3.721772] hid-generic 0003:20A0:0006.0002: input,hidraw1: USB HID v1.01 Keyboard [flirc.tv flirc] on usb-3f980000.usb-1.5/input1 [ 3.742219] systemd: Listening on Journal Socket (/dev/log). [ 4.434171] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 4.522284] systemd-journald: Received request to flush runtime journal from PID 1 [ 5.093578] snd-hifiberry-digi soc:sound: ASoC: CODEC DAI wm8804-spdif not registered - will retry [ 5.494133] wm8804 1-003b: revision E [ 5.499740] snd-hifiberry-digi soc:sound: wm8804-spdif <-> 3f203000.i2s mapping ok [ 6.653813] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 6.654423] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 8.185191] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1 [ 8.185351] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.832816] random: crng init done [ 19.832826] random: 7 urandom warning(s) missed due to ratelimiting [ 434.867577] usb 1-1.2: new high-speed USB device number 5 using dwc_otg [ 434.998642] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5575 [ 434.998649] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 434.998653] usb 1-1.2: Product: Cruzer Glide [ 434.998658] usb 1-1.2: Manufacturer: SanDisk [ 434.998662] usb 1-1.2: SerialNumber: 4C530001021015116432 [ 435.000462] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 435.001130] scsi host0: usb-storage 1-1.2:1.0 [ 436.068367] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Glide 1.00 PQ: 0 ANSI: 6 [ 436.069265] sd 0:0:0:0: [sda] 61194240 512-byte logical blocks: (31.3 GB/29.2 GiB) [ 436.069893] sd 0:0:0:0: [sda] Write Protect is off [ 436.069900] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 436.070254] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 436.077028] sda: sda1 [ 436.078767] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 436.081553] sd 0:0:0:0: Attached scsi generic sg0 type 0 Quote Link to comment Share on other sites More sharing options...
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.