zbyka Posted April 10, 2014 Report Share Posted April 10, 2014 Hello, I'd like to ask how to downgrade flirc to stable version 1.x? All links here are dead and I can't download older firmware. Currently I'm using beta fw 2.4 and I'm not satisfied (mainly because of fantom keys). May I ask for instructions how to get back to stable fw and working links or how to get rid of fantom keys and endless repeats. It's annoying. Thanks in advance. Quote Link to comment Share on other sites More sharing options...
jason Posted April 10, 2014 Report Share Posted April 10, 2014 fire up the commandline and show all the keys: flirc_util settings Any duplicate keys, remove as suspected noise: flirc_util delete_index 'index number' Where index number is the number shown in flirc_util settings next to the key. Quote Link to comment Share on other sites More sharing options...
zbyka Posted April 10, 2014 Author Report Share Posted April 10, 2014 Hello Jason, Thanks for quick response but i'm not expert in commandline. May I ask for more specific instruction how to perform operations you were writing in post above? I would be very grateful. Thanks in advance Quote Link to comment Share on other sites More sharing options...
jason Posted April 10, 2014 Report Share Posted April 10, 2014 Post your configuration here, I'll go through it for you. Quote Link to comment Share on other sites More sharing options...
zbyka Posted April 10, 2014 Author Report Share Posted April 10, 2014 This is my configuration: Harmony 650 + XBMC OpenELEC Frodo. See attachment - config from flirc software. I hope this is the file you're talking about. Flirc XBMC profile added through myharmony.com If you need additional data - let me know. Regards my_flirc_config.fcfg Quote Link to comment Share on other sites More sharing options...
jason Posted April 10, 2014 Report Share Posted April 10, 2014 the only duplicate I see is the 'i'. I can't remove that just yet until I get home. Why did you enable the XBMC profile, and record keys? Basically, the xbmc profile on the flirc is matched with the one in harmony one such that you need no additional pairing. Have you tried disabling built in profiles in advanced? Quote Link to comment Share on other sites More sharing options...
zbyka Posted April 11, 2014 Author Report Share Posted April 11, 2014 Hello Jason, Sorry for delay (timezone). I'm from Europe;-) I have cleared all configuration in Flirc. I start over with 2.4 FW with options: Builtin profiles, Noise canceller. No changes with default profile to Harmony 650 (from www.myharmony.com). I didn't configure any buttons with flirc software. Is it correct? What else would you suggest? Regards Quote Link to comment Share on other sites More sharing options...
jason Posted April 11, 2014 Report Share Posted April 11, 2014 Yes, just make sure built in profiles is enabled, and you can use your harmony without any change in flirc. Let me know if that helps. If there are any keys that need changing, you can map over them. Do you remember which keys were causing noise? Sincerely, Jason Quote Link to comment Share on other sites More sharing options...
zbyka Posted April 11, 2014 Author Report Share Posted April 11, 2014 Unfortunately this configuration doesn't work properly. Let me sum up: - "clear" Flirc (empty conf file) .Builtin profile & noise canceller enabled. FW2.4 - default profile Flirc XBMC taken from myharmony.com I didn't touch anything exept above. no key mapping etc. Still the same issues - fantom keys and endless repeats Any suggestions? I'm running out of ideas;-) Regards Quote Link to comment Share on other sites More sharing options...
zbyka Posted April 11, 2014 Author Report Share Posted April 11, 2014 Hi Jason, Tel me how to create syntax in order to delete one of keys. I'm trying like that: C:\Program Files (x86)\Flirc>flirc_util.exe delete_index'16' [E] run_cmds(248): could not find command 'delete_index'16' It doesn't work. Here is my flirc_util settings: flirc_util version v1.2.3 [v1.2.3] Firmware: v2.4 Settings: sleep detection: Disabled noise canceler: Enabled inter-key delay: 3 state: 0 builtin profiles: Disable Memory Info: keys recorded: 32 keys remaining: 137 memory used: 23% Recorded Keys: Index hash key ----- --------- --- 0 65F8450 1 1 25D2475F 2 2 46EB8450 3 3 A562485F 4 4 C662485F 5 5 655E485F 6 6 8687D952 7 7 2513AF61 8 8 4613AF61 9 9 E55E8450 0 10 460CD99A up 11 65BF9B4B down 12 86B71F14 left 13 25B31F14 right 14 86BF9B4B return 15 46AB894B backspace 16 65B71F14 i 17 6708498 - 18 E5261F14 = 19 257BC215 t 20 6576B811 p 21 869FAF61 space 22 6FF9C61 x 23 C633C63C r 24 A5FA9C61 f 25 C6E38398 , 26 A5E38398 . 27 6484D90 / 28 A5120D14 pageup 29 C64B9C4B pagedown 30 E5474D90 w 31 C6948ADF c I want to remove line 16 ("info" button from my harmony). This button doesn't work. Nothing happens when I press it. When I assign "Info" button with flirc software there two info buttons (I dont know why). There is some conflict between default flirc xbmc from my harmony and builtin profile from Flirc. Quote Link to comment Share on other sites More sharing options...
MrNice Posted April 11, 2014 Report Share Posted April 11, 2014 I think you should add a space between 'delete_index and 16 Don't think you need ' ' Do you run it as admin? Try all these options Sorry I can't test at this time, just some ideas. Quote Link to comment Share on other sites More sharing options...
zbyka Posted April 12, 2014 Author Report Share Posted April 12, 2014 Anyway. None of these solutions works. I need to load stable FW 1.x Still the same problems. Where can I find the working link? I would like to ask for proper link to stable FW 1.x Regards Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.