etronic Posted November 23, 2013 Report Share Posted November 23, 2013 I have a Harmony One RC and I'm getting occasional stuck auto-repeat, just wondering where this is controlled from? is it on the FLIRC device or my Linux config? You're in the same situation as me. Harmony One and I'm getting "repeat madness" from time to time on my Pi and Raspbmc. It looks like single key press triggers it more. When you hold remore button for two or more repeats and release it it never gets stuck in loop. Quote Link to comment Share on other sites More sharing options...
jason Posted November 23, 2013 Report Share Posted November 23, 2013 I've got to get to the bottom of this. Can you post pictures of your harmony settings? Advanced timing settings. Also, which remote control is it? The XBMC-Flirc profile? Post your configuration details too. ** EDIT ** I mean attach your flirc.fcfg file Quote Link to comment Share on other sites More sharing options...
Ptrax Posted November 23, 2013 Report Share Posted November 23, 2013 I'm using the older Logitech Remote s/w to config my remote ie I haven't yet migrated to MyHarmony website yet, so not sure which screen/setting your looking for... also where is thie flirc.fcfg is that some sort of export file? I've attached it. my_flirc_config.fcfg Quote Link to comment Share on other sites More sharing options...
zaphodFlirc Posted November 23, 2013 Author Report Share Posted November 23, 2013 So I've now tried two things based on feedback above: * [@STEVELEA tip] took out my USB extension cable and put the Flirc directly in the RasbPi (I now have the USB memory stick on the extension or it won't fit) * [@COBELS tip] did the troubleshooter in the Harmony software and put the value to 1 (it was on 3 or 4 - can't remember) And it SEEMS that it is now working without the horrendous repeats. I'll give it a few more tries and post back. [post 3 hours later: seems stable still after removing the USB extension + turning the "to much to little value" down to 1. Will this finally be the resolution after months and months of annoyance? I really do hope so!] Quote Link to comment Share on other sites More sharing options...
Ptrax Posted November 23, 2013 Report Share Posted November 23, 2013 FYI my Responding ,to much to little value was /is : 1 , so that wasn't my issue. Quote Link to comment Share on other sites More sharing options...
jason Posted November 24, 2013 Report Share Posted November 24, 2013 can you guys post screen shots of these. I don't know what you are referring too. I need to repeat the setup. Quote Link to comment Share on other sites More sharing options...
jason Posted November 24, 2013 Report Share Posted November 24, 2013 I'm using the older Logitech Remote s/w to config my remote ie I haven't yet migrated to MyHarmony website yet, so not sure which screen/setting your looking for... also where is thie flirc.fcfg is that some sort of export file? I've attached it. The configuration on your flirc is definitely broken. Upload the attached, and then try recording your keys again. I bet that fixes it. Quote Link to comment Share on other sites More sharing options...
Ptrax Posted November 24, 2013 Report Share Posted November 24, 2013 The configuration on your flirc is definitely broken. Upload the attached, and then try recording your keys again. I bet that fixes it. ok I'll try and do config from windows and then re-plug into Linux box right? but attached a screen shot of RC config page. ie I use the Trouble shoot button then select device and then "Responds to some commands either too many times or occasionally. Quote Link to comment Share on other sites More sharing options...
jason Posted November 24, 2013 Report Share Posted November 24, 2013 ok I'll try and do config from windows and then re-plug into Linux box right? but attached a screen shot of RC config page. ie I use the Trouble shoot button then select device and then "Responds to some commands either too many times or occasionally. What's the remote control? I know it's a harmony, but what's the profile? Samsung? Panasonic? Flirc? Something else? Quote Link to comment Share on other sites More sharing options...
zaphodFlirc Posted November 27, 2013 Author Report Share Posted November 27, 2013 It really looks like it has been resolved for me. Now a few days later, and I don't think I've had even one single repeat. And I haven't heard the kids complain about it either :) What did it for me (I really advise you to try this as well) was: * [@STEVELEA tip] took out my USB extension cable and put the Flirc directly in the RasbPi (I now have the USB memory stick on the extension or it won't fit) * [@COBELS tip] did the troubleshooter in the Harmony software and put the value to 1 (it was on 3 or 4 - can't remember) STEVELEA and COBELS are now officially my heroes. Thanks guys (assuming you're guys that is...) 1 Quote Link to comment Share on other sites More sharing options...
dantist Posted November 23, 2014 Report Share Posted November 23, 2014 Neither Stevelea nor Cobels tips solved the problem for me. I just downloaded the latest GUI to update the firmware. When I chose "Force FW upgrade" it says my flirc already has the latest one (3.1). But I haven't updated since a year or so. Is this done automatically as soon as you connect the device and start the GUI? I also selected "Noise Canceler" in the settings, because that sounded like it could address the issue. But the behavior is the same: When I press the button to skip a few seconds of a movie, it goes crazy every now and then and keeps skipping 3-4 times per seconds until I press another button or disconnect flirc. tail -f /storage/.xbmc/temp/xbmc.log shows that they XBMC recognizes the key press 12-14 times second 17:45:07 T:3058148128 DEBUG: OnKey: right (0xf083) pressed, action is StepForward Very frustrating. Quote Link to comment Share on other sites More sharing options...
GoodOmens Posted November 23, 2014 Report Share Posted November 23, 2014 Ok so the Harmony 900 sends RF signals to a base unit that converts the RF into IR signals. The base unit then sends the IR signals out via the mini IR blasters (IR senders). You place the blasters in front of your Home Theatre (HT) equipment so that your remote can control multiple devices. I had my home theatre equipment (XBMC box, DVR and Apple TV) all in the same cabinet, each with their own harmony mini-blaster. The harmony sends the IR signals to ALL of the mini-blasters at the same time. eg. If I wanted to play a movie on XBMC I'd press "play" on my remote and the harmony would send the IR signal to all of the mini-blasters BUT only the XBMC would react to the play signal because the other devices (DVR and Apple TV) wouldn't recognise the IR signal being sent). The problem for me was because the IR signal is sent to all three mini blasters the FLIRC was picking up the 3 IR signals at the same time causing it to go crazy. I had to move the flirc to a position where it would only pick up the signal from one IR blaster (not all three). I did this by moving my XBMC/FLIRC and one IR blaster outside of the cabinet away from the other 2 IR blasters. This solved my problem instantly. Hope that makes sense. Jeremy. You can in settings tell the rf receiver to assign a port to a specific device. Quote Link to comment Share on other sites More sharing options...
jason Posted November 23, 2014 Report Share Posted November 23, 2014 I've been following this thread religiously and there are two problems that can happen and the multiple people posting are either experiencing one or the other. Flirc is essentially a keyboard, so consider Problem 1) When you hit a key on the remote, one key is received on your machine, there is a delay, and then several keys are seen. Like if you had a keyboard and just pressed and held the button down. 2) When you hit a key, several keys are received rapidly. These are two very different problems and users aren't distinguishing them here, and rightfully so, as the problem statement is too many keys are received. So let's talk about the solutions we've figured out. 1a) If you have a harmony remote, lower the repeat value in the harmony software: in the remote, go to the troubleshooter and lower the value to 0 or 11b) if you don't, lower the interkey_delay in the flirc advanced software. 2a) raise the interkey_delay in the flirc advanced software I think there is one more cause for 2, but I haven't determined what it is yet, I'm still working on it. It's going to require some special firmware that I started on. I'll put a sticky at the top of this thread for others, this seems to be the solution. [edit by Chris: A separate sticky has been made to make the issue easier to find for those who may be experiencing it. Continue to discus it here though] Quote Link to comment Share on other sites More sharing options...
dantist Posted November 29, 2014 Report Share Posted November 29, 2014 (edited) > 1a) If you have a harmony remote, lower the repeat value in the harmony software: in the remote, go to the troubleshooter and lower the value to 0 or 1 The value was set to 1, I changed it to 0. If anything, this made the problem worse. > 2a) raise the interkey_delay in the flirc advanced software The value was already set to 6, which is the maximum. To be honest, I doubt that these settings are targeting the root cause of the problem. It would make sense that a higher delay / lower repeat value helps with double key presses, but the problem here is that one physical key press triggers infinite key presses in the software. Maybe it's not even a bug in your firmware but in the RPi service that handles the messages that are sent via flirc? But then I don't understand why a Logitech K400 is working flawlessly. Edited November 29, 2014 by dantist Quote Link to comment Share on other sites More sharing options...
dantist Posted December 4, 2014 Report Share Posted December 4, 2014 (edited) Update: I set the repeat value in the Harmony remote flirc-profile to "2", which greatly improved the issue. I only had a few double/endless repeats within the last five days. Edited December 6, 2014 by dantist Quote Link to comment Share on other sites More sharing options...
Din Posted March 2, 2015 Report Share Posted March 2, 2015 (edited) Prior to the arrival of my FLIRC and Xbox one media remote I'd been using the official XBMC Android remote application to control both XBMC on an Ubuntu / Win PC and also OpenElec on a Raspberry Pi and a Cubox-i. I too had the endless repeat problem on the PC, Pi and Cubox-i. That was until I selected the 'Send Single Keypress' option in the application's settings. Thereafter everything has been smooth and error free. With only the slight inconvenience of thumb ache while navigating the occasional long list or large media library. I had hoped that my new remote would seamlessly replace the smartphone - it's a pain having to boot up a phone every time you want to play a video / track - but I was disappointed to re-encounter the same problem with endless repeats. Though this time without an obvious solution: I've tried every inter key delay, and selecting and deselecting all the advanced options but find the remote is still almost completely unusable. The application solution and the problems others have encountered suggest to me that perhaps the problem is with the Kodi/XBMC software and not the FLIRC firmware. And that until the root cause is remedied it might be an idea to circumvent the annoyance by adding a 'Send Single Keypress' option to FLIRC's settings. That's if it's technically possible. And not too much work. Thanks for your time and hope this helps. Thomas Edited March 2, 2015 by Din Quote Link to comment Share on other sites More sharing options...
Din Posted March 2, 2015 Report Share Posted March 2, 2015 (edited) Please ignore my whinge above. I discovered a solution to my double keypress issue when I accidentally held the Xbox One Media remote back to front. If I point the remote directly at the FLIRC then I get the usual over enthusiastic response. But if instead I point the remote 180 deg or 90 deg to either side then everything works just fine. As it does with my preferred option of obscuring the Cubox-i & FLIRC behind the TV with the FLIRC 180 deg to the remote. I am now very happy with both the remote and FLIRC. And a little embarrassed about the previous post. Is the problem that FLIRC is just too potent for its own good? Edited March 3, 2015 by Din Quote Link to comment Share on other sites More sharing options...
jason Posted March 2, 2015 Report Share Posted March 2, 2015 are you on 3.5 or 3.6 of the firmware? Quote Link to comment Share on other sites More sharing options...
jason Posted March 2, 2015 Report Share Posted March 2, 2015 I like that word, potent. Yes, super sensitive. May help to re-pair you remote and point it away from flirc. Quote Link to comment Share on other sites More sharing options...
Din Posted March 3, 2015 Report Share Posted March 3, 2015 I'm using the 3.5 firmware. But by an astonishing co-incidence just as I finished typing the last sentence an Ubuntu update notification told me that I could update to 3.6. I've done just that and everything is still tickety-boo. Quote Link to comment Share on other sites More sharing options...
jason Posted March 3, 2015 Report Share Posted March 3, 2015 Yeah, I forgot I updated my manufacturing line to use a newer firmware for new devices and those started shipping. Latest GUI's didn't support those, so I had to quickly release an update. Oops. Slaps forehead. 2 Quote Link to comment Share on other sites More sharing options...
wsmeyer Posted June 29, 2015 Report Share Posted June 29, 2015 I'm now experiencing this. For over a year my setup worked perfectly: intel i3 NUC Windows 7 Pro always kept up to date Only software installed - Plex Home Theater, Firefox, flirc XBOX One Media Remote ( http://ecx.images-amazon.com/images/I/61Pwgq%2B8xeL._SL1300_.jpg ) Last Friday I purchsed the newer 5th gen i5 NUC, installed the same W7 Pro, let it do all it's updates, PHT, Firefox, flirc, and of course now, just randomly when I press a key it goes berzerk as if I'm holding down the key. I DID NOT reprogram or do anything to the flirc so I'm really not sure what is different between the old and new setup that could cause this. I have seen people mentioning power supplies. The new NUC has a different power supply so when I get home I'll check if the old and new are the same voltage and if so try the olde one. Quote Link to comment Share on other sites More sharing options...
wsmeyer Posted June 30, 2015 Report Share Posted June 30, 2015 Changing the power supply completely solved my problem. I am quite happy that it is again working perfectly. The problem is completely reproduceable / fixed by swappinmg the new / old power supplies. The older i3 NUC came with a two piece power supply. 3 prong power cord plugging into a brick with a cable then plugging into the NUC. The newer i5 came with a much smaller 2 prong one piece unit, usually referred to as a "wall wart". Both 19VDC 3.42A. Quote Link to comment Share on other sites More sharing options...
nixpix Posted January 30, 2016 Report Share Posted January 30, 2016 I am also experiencing this issue. I've had my flirc 2 weeks and it mostly working great, with the one exception of sometimes repeating keys endlessly. What happens is what many others here reported - pressing one key once on the remote and flirc outputting command endlessly, it keeps sending presses inifinitely until another key is pressed on the remote.The remote is not a Logitech harmony though, as many others have, its a remote originally shipped with a Dune HD Smart B1 mediastreamer. Firmware is 3.6 with inter key delay 5. I have checked that the remote does not send repeating keys. I have also tried the noise cancelling option, and it does seem to help, but then instead the remote reacts extremely sluggish and has a delay between accepting presses, like press one key then wait 1-2sec and then press again.I am using flirc on an Asus chromebox with Kodi 15.2/openELECT 6.0 fritsch EGL build. Quote Link to comment Share on other sites More sharing options...
jason Posted January 31, 2016 Report Share Posted January 31, 2016 Definitely try changing the interkey delay settings, it shouldn't get stuck. How often does this happen? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.