a.l3881 Posted July 30, 2017 Report Posted July 30, 2017 (edited) Hi, I configured Flirc to control the Sunrise TV Box UHD (Swiss internet provider). This box is manufactured by Sagemcom (DIW384 UHD) and is controlled by a bluetooth remote. Below the list of all remote command that I found using the command line function: Power flirc_util record_api 48 102 red flirc_util record_api 105 102 green flirc_util record_api 106 102 yellow flirc_util record_api 108 102 blue flirc_util record_api 107 102 TV Guide flirc_util record_api 141 102 Back/Cancel flirc_util record_api 70 102 Info flirc_util record_api 149 102 OK flirc_util record_api 65 102 UP flirc_util record_api 66 102 DOWN flirc_util record_api 67 102 LEFT flirc_util record_api 68 102 RIGHT flirc_util record_api 69 102 Recordings flirc_util record_api 153 102 Menu flirc_util record_api 64 102 Volume up flirc_util record_api 233 102 Volume down flirc_util record_api 234 102 Mute flirc_util record_api 226 102 Channel UP flirc_util record_api 156 102 Channel Down flirc_util record_api 157 102 Play/Pause flirc_util record_api 205 102 Fast forward flirc_util record_api 179 102 Fast rewind flirc_util record_api 180 102 REC flirc_util record_api 178 102 Next flirc_util record_api 181 102 Back flirc_util record_api 182 102 The keypad can be programmed using the Flirc application and by simulating a standard keyboard. Thanks to yawor for his post explaning this function : Config for the logitech Harmony HUB This is the last config I am using now : https://www.dropbox.com/s/mptca2zqjcqvtmd/Sunrise_Flirc.fcfg?dl=0 You can use the config file without learning the commands (they are saved in the flirc config file). flash your Flirc dongle from the PC or MAC with the config file Connect the Flirc to the usb port of the sunrise tv box. Make sure that the harmony hub can send the IR signal to Flirc dongle. Add the sunrise tv box from the harmony application : Now you can validate that it works in the next screen from the harmony application : Edited September 6, 2017 by a.l3881 Add config file and Harmony application config 1 Quote
GodziFa Posted September 16, 2017 Report Posted September 16, 2017 Hi! I thank you very much for sharing your config file! As I don't have an HID keyboard, I cannot add number 0 to 9 in your config file. Could you add those command line functions? I thank you in advance! Quote
a.l3881 Posted September 18, 2017 Author Report Posted September 18, 2017 Hello, Here a new config file with the numbers : Flirc_18.09.17.fcfg You can add the numbers without a keyboard, just by selection the Full keyboard from the Controllers Menu : 1 Quote
GodziFa Posted September 19, 2017 Report Posted September 19, 2017 Hello, Thanks for the new file! I tried what you said but I think I made something wrong... Quote
a.l3881 Posted September 19, 2017 Author Report Posted September 19, 2017 Hello, You can import the config file and plug back the flirc to the sunrise UHD box. The file work for the Logitech Harmony HUB by simulating the old Sunrise TV Box that have the IR remote. Quote
Zwickel Posted September 30, 2017 Report Posted September 30, 2017 Hello, Thanks for the file. Unfortunately some commands are missing. It lacks the STOP, RECORDINGS and the BACK button. Despite my efforts, Ido not get to bring the keys to run. I hope you get it. Many thanks Quote
a.l3881 Posted October 1, 2017 Author Report Posted October 1, 2017 Hello, There is no stop button on the sunrise remote. The recordings and back commands work fine in my setup. You can add them to your setup by using the command : Recordings flirc_util record_api 153 102 Back/Cancel flirc_util record_api 70 102 Quote
Zwickel Posted October 2, 2017 Report Posted October 2, 2017 Hello, I found the right (for me!!) command for record. Recordings flirc_util record_api 154 102 Thanks Quote
Christo976 Posted October 8, 2017 Report Posted October 8, 2017 (edited) Hi, Thank you for sharing your work with the community. Unfortunately it doesn't work for me :-( I connect my Flirc USB to my computer. I open the Flirc app. The app upgraded the firmware of the USB key. I go to the menu File > Load configuration and I select your file "Sunrise_Flirc.fcfg" The app confirmed "File restored". I connect the Flirc USB to the Sunrise UHD TV box I follow your instructions by adding the Sunrise Tv box as new device to my harmony remote When the Harmony app tries to turn on the device, it doesn't work. I checked that one of the IR emitter of the Harmony Hub is placed in front of the Flirc USB. But it doesn't work.....very frustating Did I forgot something ? Thank you in advance for your help. Chris Edited October 8, 2017 by Christo976 Quote
a.l3881 Posted October 9, 2017 Author Report Posted October 9, 2017 Hi Christo976, You can test adding the command using : flirc_util record_api 48 102 Zwickel found that the command can be different for the recording. I don't know if there is difference in the Sunrise UHD TV box soft. You can try replacing the command 48 by the numbers next to it. Quote
Dany Schibli Posted October 13, 2017 Report Posted October 13, 2017 Bonjour a.l3881 ! Merci beaucoup pour ces informations ! Je suis comme Christo976. J'ai fait toutes les étapes de l'installation. Mais rien ne se passe, la TV Box ne s'allume pas. J'utilise une Harmony 650, sans HUB. Google translate : Hello a.l3881 ! Thank you for this information ! I'm like Christo976. I did all the steps of the installation. But nothing happens, the TV Box does not turn on. I use a Harmony 650, without HUB Quote
GodziFa Posted October 14, 2017 Report Posted October 14, 2017 Christo976, Dany Schibli, I had some problem with Power On and Power Off the Sunrise TV Box UHD also. I tried to change flirc_util record_api 48 102 by 47 or 49 but it didn't work. In fact, the Sunrise box was powering on but I couldn't get any sound or image. I realised that my A/V receiver (Onkyo TX-NR-535) was bugging the Sunrise Box (especially when powering off). Despite I deactivated all "HDMI through" function of my devices, or even when I activated them, it was still bugging. My configuration was like that: Sunrise TV Box UHD <-HDMI-> Onkyo <-HDMI-> TV I changed like that now: Sunrise TV Box UHD <-HDMI-> TV <-Optical-> Onkyo. So for now it works. But I don't know if I could get Dolby Sourround or DTS sound in that configuration. All this to say to check your A/V receiver if you have one and make some trials by bypassing it. Quote
a.l3881 Posted October 17, 2017 Author Report Posted October 17, 2017 Hello, The power command woks for my config but I keep the sunrise TV BOX always ON and switch OFF only the TV when I end the Sunrise activity in the Harmony config. I use this config because my TV and the the sunrise TV BOX are sometime desynchronized (one is ON and the other is OFF) when the activity start or end. So if the others commands works, you can just switch ON the sunrise TV BOX with the sunrise remote and keep it always ON. Quote
GodziFa Posted October 17, 2017 Report Posted October 17, 2017 I tried to power off only my TV and my A/V receiver but as soon as I power on them, I lost the image on my Sunrise TV Box UHD. I don't why, my A/V receiver sends a signal to my Sunrise box and my TV despite I deactivated this kind of feature. Quote
dude Posted December 26, 2017 Report Posted December 26, 2017 It is working quite well. But the Recordings function is still missing. I want to have it on the DVR button of my Harmony Ultimate remote. How do I accomplish that? Quote
maisen20 Posted February 6, 2018 Report Posted February 6, 2018 Hello and thanks a lot for the help, my sunrise uhd box is partically working, but unfortunately is my „back“ button not working as it should. in the menu i can exit with the back button on my harmony elite, but i can‘t go back in menus where it shoud really trigger the „back“ command and not the „exit“. i already tested some settings by the line command and record_api, but i never get the right record_api numbers in the command line. what‘s the best way to get the right number for the command? Quote
Pether Posted February 10, 2018 Report Posted February 10, 2018 Hi, this all works very well except for the "Netflix" button that is on the latest Sunrise box remote I can get to netflix using the "menu" button , but once in netflix the "ok" button doesnt seem to work so I cant select a profile. Has anyone figured this out? Quote
a.l3881 Posted February 10, 2018 Author Report Posted February 10, 2018 Hello maisen20 and Pether, I found these code by pairing the Flirc with an old remote control, and tested all the possible number for the command record_api xxx 120 (from 0 to 255). For the Back/Exit command, I found just one command number (flirc_util record_api 70 102). Sorry maisen20, I did't found the back specific number. For the OK command, I found two command number (flirc_util record_api 65 102 and flirc_util record_api 132 102) I don't use Netflix, so I cannot confirm if it works, but you can try the second command for "OK" flirc_util record_api 132 102 Quote
maisen20 Posted February 10, 2018 Report Posted February 10, 2018 Hello, thank you for your answer! i tested numbers from 1-110 and will test more in the next days, i already found a lot commands but not the specific back button. maybe i will post my experience with all the numbers here. thank you for your work! Quote
Watterli Posted February 12, 2018 Report Posted February 12, 2018 Hello With the above informations I could manage to run the Sunrise TV Box with the Harmony Elite. The only thing I had to change, was the command for the recordings. Did anyone find out the command for the "Teletext"? Quote
piksaw Posted February 12, 2018 Report Posted February 12, 2018 Salut tout le monde j ai suivi les instructions mais ça ne marche pas quelqu’un aurai un fichier qui fonctionne svp Quote
piksaw Posted February 13, 2018 Report Posted February 13, 2018 hi. sorry for my english how can i add the command with flirc Quote
a.l3881 Posted February 13, 2018 Author Report Posted February 13, 2018 Hello piksaw, You can try with this new config file : https://www.dropbox.com/s/3wjt2z4zxck6lqd/my_flirc_config_10.02.18.fcfg?dl=0 Use the command "flirc_util loadconfig" In the harmony settings use the old sunrise box as device to send the command. Quote
piksaw Posted February 13, 2018 Report Posted February 13, 2018 (edited) :-( I don’t work I have a harmony elite In the harmony setting use sunrise Tv box Edited February 13, 2018 by piksaw Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.